Pull Rope Emergency Stop Switch

Conveyors may run out of line, causing major damage. For this reason, misalignment switches are provided to register belt misalignment and to switch off the belt if necessary.

Kiepe pull rope emergency stop switches are emergency stop devices with latch function. They are operated by pulling or tearing the pull rope. Reset is carried out manually at the device. For safe pull rope installation, "Components for Pull Rope System" are required whose functions are tailored to Kiepe pull rope emergency stop switches and the respective applications.

The safety data of the electromechanic switches have been specified according to DIN EN ISO 13849-1. You can find the information about safety data B10d and performance level (PL) at the product pages or in the brochures.

Quick-Clamp System

It only takes one single person to reliably install the double-sided pull-rope system. In just a few installation steps, the pull rope can be connected, tensioned and adjusted over its entire length. Only in the last step the pull rope is connected to the pull-rope switch with a new KIEPE Clamp Assembly. The assembly has been significantly simplified with improved safety performance compared to conventional methods.

The new Kiepe Quick-Clamp System

Overview Pull Rope Switches

Pull Rope Emergency Stop Switch Type PAS

enclosure: PBT-Plastic - Pull Rope Lenght: up to 1x30m - one side installation - adjustment aid for operating point contact configuration: 1 changeover contact / 1 NC (positive-break contact - self cleaning)

Pull Rope Emergency Switch Type LRS

enclosure: Aluminum - Pull Rope Length: up to 1x 20m - oneside installation - with read out indicator for operating point - Emergency Stop Button

Pull Rope Emergency Stop Switch Type PRS

enclosure: PBT-Plastic - Pull Rope Length: 2x50m - two-sided installation contact configuration 2 NC / 1 changeover contact (positive-break contacts)

Pull Rope Emergency Stop Switch Type HEN

enclosure: Aluminum - Pull Rope Length: up to 2x 50m - two-sided installation contact configuration: maximum 3NC/ 3NO (positive-break contacts)

Pull Rope Emergency Stop Switch Type HEN 211

with two(2)-wire- Bus Terminal - enclosure: Aluminum - Pull Rope Length: up to 2x 50m - two-sided installation contact configuration: 2NC and 1NO for BUS-control (positive-break contacts) Bus-Signal only for control circuits

Pull Rope Emergency Stop Switch HEN 221/231 SafetyBus

with SafetyBus Module - enclosure: Aluminum - Pull Rope Length: up to 2x 50m - two-sided installation contact configuration: SafetyBus-Signal

Pull Rope Emergency Stop Switch Type NTS

enclosure: BMC-Plastic - Pull Rope Length: up to 2x 50m - two-sided installation contact configuration: max. 3 NC / 3 NO (positive-break contacts)

Pull Rope Emergency Stop Switch Type SEG

enclosure: cast iron - Pull Rope Length: up to 2x 50m - two-sided installation contact configuration: maximum 3 NC / 3 NO (positive-break contacts)

EX Pull Rope Switches

Devices, which are approved for use in hazardous areas with explosive atmosphere, can be found in the folder "EX Pull Rope Switches", except for underground mining applications.

Overview EX Pull Rope Switches

HEN EX

Zone 21 and/or 22: combustible , conductible dust - Enclosure: Aluminium - Pull rope length up to 2x 50m - two-side installation - Contact configuration: up to 3 NO and 3 NO positive-making contacts Permissible ambient Tempertature: -25°C up to +70°C Application: - HEN EX xxx 2D : Devices for Zone 21 and 22 (2D) - HEN EX xxx 3D : Devices for Zone 22 (3D)

SEG EX

Zone 21 and/or 22: combustible , conductible dust - Enclosure: Cast Iron - Pull rope length up to 2x 50m - two-side installation - Contact configuration: up to 3 NO and 3 NO positive-making contacts Permissible ambient Tempertature: -25°C up to +70°C Application: - SEG EX xxx 2D : Device for Zone 21 and 22 (2D) - SEG EX xxx 3D : Device for Zone 22 (3D)

back to product overview